1. Do not unilaterally consider the elements such as "tension edge and pressure edge" on the brace hole of purlin, and make holes with unequal upper and lower edge spacing, because the equipment is simply installed reversely, and the effect is unlucky.

2、门窗等的包角板不能相提并论，因为在施工中你无法保证板件位于压型板的波峰仍是波谷。

2. The angle wrapping plates of doors and windows can not be compared, because you can't guarantee that the plates are located at the crest or trough of the profiled plate during construction.

3、做大型工程时，深化图编号一定要考虑到出产、发货、设备的便捷。

3. When doing large-scale projects, the convenience of production, delivery and equipment must be taken into account in deepening drawing numbering.

4、假设有天沟，系杆不能计划到紧贴着柱顶的部位，否则将或许致使无法设备落水管。另外天沟落水管和系杆以及柱间支撑的方位一定要考虑好，否则要么碰到系杆，要么碰到柱间支撑。

4. If there is a gutter, the tie rod cannot be planned to be close to the top of the column, otherwise the equipment downpipe may not be available. In addition, the orientation of gutter downpipe, tie rod and inter column support must be considered, otherwise it will either encounter tie rod or inter column support.

5、成都活动板房水平支撑上花篮螺栓方位的安顿要合理，不要过于违背主梁，应当考虑便当设备为主。否则工人在设备时有必要探出身子来拧紧花篮螺栓或许用爬梯上去，要么等檩条设备结束后爬上檩条拧紧花篮螺栓这样非常不。另外也要考虑一下隅撑的安顿方位，不要在安顿水平支撑时与隅撑打架。

5. The orientation of flower basket bolts on the horizontal support of Chengdu movable plank house shall be reasonable, not too contrary to the main beam, and convenient equipment shall be considered. Otherwise, it is necessary for the workers to lean out to tighten the flower basket bolts during the equipment, perhaps climb the ladder, or climb up the purlin to tighten the flower basket bolts after the purlin equipment is completed, which is very unsafe. In addition, consider the setting position of the corner brace, and do not fight with the corner brace when setting the horizontal support.

6、对甲方供给的“荷载等数据”一定要了解其实在的意思，因为甲方一般不太懂这些太的东东。我们要做到换位考虑，前期工作做好了，后续工作就好打开的多了。

6. We must understand the meaning of "load and other data" provided by Party A, because party a generally does not understand these things. We should consider transposition. If the preliminary work is done well, the follow-up work will be much easier to open.

7、高强螺栓的方位要合理，要考虑扭断器及扭矩扳手的施工空间，不要在设备时，因为空间太小，扭断器及扭矩扳手无法就位等，致使高强螺栓梅花头无法拧断或高强螺栓无法拧紧。曾经碰到过有的计划连套筒的方位都不给。

7. The orientation of the high-strength bolt shall be reasonable, and the construction space of the torsion breaker and torque wrench shall be considered. Do not use the equipment because the space is too small and the torsion breaker and torque wrench cannot be in place, so that the ring head of the high-strength bolt cannot be screwed off or the high-strength bolt cannot be tightened. I have encountered some plans that don't even give the orientation of the sleeve.

8、高强螺栓联接板假设有或许，尽量选用上下对称的螺栓安顿办法。曾经有中接点上面4个下面6个，车间工人搭装不小心将一部分搞反了，在现场对不住来。

8. If the high-strength bolt connecting plate is false, try to use the bolt installation method with symmetrical up and down. Once there were 4 middle contacts above and 6 below. The workshop workers accidentally reversed some of them. I'm sorry at the scene.

9、轻钢结构假设有保护砖墙，一定要提早与建设单位及土建施工单位对接好，因为这涉及到土建和钢结构两个方面的疑问，因为土建的砖墙很或许搞不平直，可彩钢板的泛水又不或许做得忽大忽小，

9. If the light steel structure is provided with protective brick walls, it must be connected with the construction unit and civil construction unit in advance, because this involves the questions of civil engineering and steel structure, because the brick walls of civil engineering may be uneven, but the flashing of color steel plate may not be large or small,