彩钢板长期使用会老化。若老化严重，将影响钢板的正常使用，带来隐患。所以，使用时应注意观察电路板的使用情况。出现老化现象后可进行修复。那装修施工的具体步骤是什么呢？济南彩钢厂家为您解析。

Color steel plate will age after long-term use. If the aging is serious, it will affect the normal use of the steel plate and bring potential safety hazards. Therefore, the use of the circuit board should be observed. The aging phenomenon can be repaired. What are the specific steps of decoration construction? Jinan color steel manufacturers analyze for you.

1.彩钢板底部的底板，并进行除锈打磨。

1. Remove the bottom plate of the color steel plate, and conduct rust removal and polishing.

2.采用防腐专用底漆施工，对该夹芯板锈蚀特别严重的部位，应采用重防腐底漆喷涂处理。

2. The special anti-corrosion primer shall be used for construction. The parts of the sandwich panel with severe corrosion shall be sprayed with heavy anti-corrosion primer.

3.由于彩钢岩棉夹心板厚度为0.32mm，采用防腐专用面层喷涂二次。

3. As the thickness of color steel rock wool sandwich plate is 0.32mm, it is sprayed twice with a special anti-corrosion surface layer.

4.使用刷子涂或喷涂滚筒。

4. Brush or spray the roller.

表面清理：

Surface cleaning:

1.脱漆：原有漆膜涂层老化、起鼓、剥皮、旧漆膜须用铲刀将其刮静。

1. Paint stripping: the original paint film coating is aged, bulged, peeled, and the old paint film must be scraped with a blade.

2.除锈：将已发生锈蚀的氧化皮及翘起、龟裂的部位用铲刀、钢丝刷、纱布和磨光机等工具打磨干净，金属表面应达到无锈蚀、无油污、无杂物，并露出均一的金属光泽，除锈等级达到St3 级标准，同时除锈部位与保留的旧漆层边缘须有平滑过度。

2. Derusting: The rusted oxide skin and the parts with warping and cracking shall be polished with shovel, wire brush, gauze, polishing machine and other tools. The metal surface shall be free of rust, oil stain and sundries, and the uniform metallic luster shall be exposed. The derusting grade shall meet the St3 standard. At the same time, the derusting part and the edge of the retained old paint layer must be smooth.

3.打磨和清洗：表面脱漆除锈后，须用砂轮或粗布对其打磨，磨出一定的粗糙度，增强油漆的附着力，然后进行清洗，达到金属表面无杂物、灰尘等。

3. Grinding and cleaning: After the surface is stripped of paint and derusted, it must be polished with a grinding wheel or rough cloth to obtain a certain roughness, enhance the adhesion of the paint, and then cleaned to ensure that the metal surface is free of debris, dust, etc.

4.对于有油渍的地方，需要先用清洗剂清理干净。

4. Oil stains shall be cleaned with detergent first.

标准：清理后，管道、罐体、支架、设备等防腐表层要求无浮尘、无浮锈、无层锈、无鼓包和翘皮的漆层、无砂浆疙瘩、无油渍和化学腐蚀物。 作者：代诺重防腐防锈涂料 https://www.bilibili.com/read/cv11986023/ 出处：bilibili

Standard: After cleaning, the anti-corrosion surface of pipes, tanks, supports, equipment, etc. shall be free of floating dust, floating rust, layer rust, bulged and warped paint, mortar bumps, oil stains and chemical corrosives. Author: Danuo Heavy Anti corrosion and Anti rust Paint https://www.bilibili.com/read/cv11986023/ Origin: bilibili

彩钢板的翻新过程还是比较简单的，在翻新时要注意把底板的底面打磨干净，把生锈的地方磨平，接着进行涂料喷刷，记得要喷刷均匀，这样才能保证表面牢固度不容易脱落，相信大家掌握以上方法后可以很好的进行翻新工作。更多相关内容就来我们网站http://www.lxcaigang.com咨询看看吧！

The renovation process of color steel plate is relatively simple. During the renovation, the bottom surface of the base plate should be polished clean, the rusty area should be smoothed, and then the paint should be sprayed evenly, so as to ensure that the surface firmness is not easy to fall off. I believe that you can carry out the renovation work well after mastering the above methods. Come to our website for more http://www.lxcaigang.com   information!