钢结构厂房如何施工，钢结构厂房施工工艺:钢结构厂房本身具有重量轻、强度高、抗压能力强、施工周期短等特点。

How to construct a steel structure factory building and its construction technology: The steel structure factory building itself has the characteristics of light weight, high strength, strong compressive capacity, and short construction period.

钢结构厂房具体施工工艺：

Specific construction technology for steel structure factory buildings:

1.钢结构厂主要结构吊装：地面拼接钢梁、钢柱架设、钢梁吊装、连接子结构、纠正主体结构偏差、安装起重梁(可选)、吊装夹层(可选)、涂防火涂料。

1. Main structural lifting in steel structure factory: ground splicing of steel beams, installation of steel columns, lifting of steel beams, connection of substructures, correction of main structural deviations, installation of lifting beams (optional), lifting of intermediate layers (optional), and application of fire-resistant coatings.

2.钢结构厂房二次结构安装：屋面墙檩条、屋面墙支撑、翼缘支撑等。

2. Secondary structure installation of steel structure factory building: roof wall purlins, roof wall supports, flange supports, etc.

3.钢结构厂房屋面板及保温层安装：先铺设保温层，再安装屋面板（部分工程仍在保温层下铺设钢丝网，防止保温层脱落，主要取决于保温层等级）。屋顶主要是防水的。因此，有必要将广告牌与木板重叠，钉板，胶水应满但不满意，胶水应清洗，板表面涂层不应损坏，防止腐蚀等。

3. Installation of Steel Structure Factory House Panel and Insulation Layer: First lay the insulation layer, then install the roof panel (some projects still lay steel wire mesh under the insulation layer to prevent the insulation layer from falling off, mainly depending on the insulation layer level). The roof is mainly waterproof. Therefore, it is necessary to overlap the billboard with the wooden board, nail the board, and ensure that the glue is full but not satisfactory. The glue should be cleaned, and the surface coating of the board should not be damaged to prevent corrosion.

4.钢结构厂房自身墙体的维护安装:主要安装墙体保温层和墙板。墙体主要是窗户区域的美观和防水。还有确定安装是否有偏差的问题。比如底部要平整，整个平面要平整，板与板之间的平整度偏差要符合要求。

4. Maintenance and installation of the steel structure factory building's own walls: mainly installing wall insulation layer and wall panels. The wall mainly focuses on the aesthetics and waterproofing of the window area. There is also the issue of determining whether there is any deviation in the installation. For example, the bottom should be flat, the entire plane should be flat, and the flatness deviation between boards should meet the requirements.

5.钢结构标准厂房细节结构:主要是一些装修安装，如屋面与墙面之间的角落、角落、墙板与砖墙之间的防水板、门窗装饰等。细节结构是美容工程的一个环节，也是主要组成部分之一，所以水平、平面和垂直是基本的。

5. Steel structure standard factory building details: mainly for decoration and installation, such as corners and angles between roof and wall, waterproof boards between wall panels and brick walls, door and window decorations, etc. The detailed structure is a part and main component of beauty engineering, so horizontal, flat, and vertical are fundamental.