In recent years, China's economic construction has made great progress, the building steel bearing plate industry has also developed, and its application field has been greatly expanded. However, many consumers do not know, color steel sheet room in the use process will encounter a variety of problems. In order to avoid problems in the construction process, what are the requirements of color steel plate installation construction?

Jinan color steel plate house

彩钢板房安装要求：

Installation requirements of color steel sheet room:

一、现场核查

1、 On site verification

1、设备定位在干净的地面上初步处理后。根据设备定位和设计图纸，检查隔墙放线定位以确定现场尺寸与图纸尺寸和设备位置是否有冲突。

1. The equipment is positioned on clean ground after preliminary treatment. According to the equipment positioning and design drawings, check the setting out and positioning of partition wall to determine whether the site size conflicts with the drawing size and equipment position.

2、现场核实地面标高，看波动是否大，是否有必要将彩钢墙底部整体找平。

2. Verify the ground elevation on site to see if the fluctuation is large and whether it is necessary to level the bottom of color steel wall as a whole.

二、彩钢板安装要求

2、 Installation requirements of color steel plate

1、铝槽固定：铝槽固定前需要放线定位，偏差不超过5 mm，铝槽用M5x30抽芯铝拉钉固定，间接不超过300mm。双拉销应设置在有门洞的位置，间距不应超过50毫米。

1. Aluminum groove fixation: before fixing the aluminum groove, the setting out and positioning shall be conducted, and the deviation shall not exceed 5 mm. The aluminum groove shall be fixed with m5x30 core pulling aluminum stud, and the indirect distance shall not exceed 300 mm. The double pull pin shall be set at the position with door opening, and the spacing shall not exceed 50 mm.

2、T型挂梁：的固定挂码位于放线定位沿线，间距不大于1.20mm，T型梁与连接彩钢板固定时，需用角钢或角铁压制，不得留有缝隙。被压体需要在两块彩钢板的接缝上方。

2. T-shaped hanging beam: the fixed hanging block is located along the setting out and positioning line, and the spacing is not more than 1.20 mm. When the T-shaped beam is fixed with the connecting color steel plate, angle steel or angle iron shall be used to press, and no gap shall be left. The pressed body needs to be above the joint of two color steel plates.

3、风口安装：吊顶风口的安装应按照图纸进行，避免T型梁，墙上的排风和回风风口应安装在离地面200mm处。

3. Installation of air outlet: the installation of ceiling air outlet shall be carried out according to the drawings to avoid T-beam. The air outlet for exhaust and return air on the wall shall be installed at 200 mm away from the ground.

4、外观要求：整体安装应平直美观，无碰撞划痕，安装后才能撕掉保护膜。板缝间连接平整，板缝间距3-4mm，胶应饱满顺直，无缝隙。

4. Appearance requirements: the overall installation should be straight and beautiful, without collision scratch, and the protective film can be removed after installation. The connection between the plate joints shall be smooth, and the gap between the plate joints shall be 3-4mm, and the glue shall be full, straight and seamless.

5、每个顶板和固定板之间的固定需要三个尾部钻孔螺钉。挡土板与立板之间有固定上下接头的拉销，施工时固定，板缝需垂直。

5. Three tail drilled screws are required for the fixation between each top plate and the fixed plate. There are pull pins for fixing the upper and lower joints between the retaining plate and the vertical plate, which shall be fixed during construction, and the slab joint shall be vertical.

6、门窗安装：门窗的安装位置和开启方向应根据图纸要求确定。单扇门应尽可能位于同色钢板上，双扇门的中线应尽可能位于板缝的接缝处，以便切割后的彩色钢板可用作门板。门窗的型材连接应严密无缝隙，整个门角的保持尺寸应统一。

6. Installation of doors and windows: the installation position and opening direction of doors and windows shall be determined according to the drawing requirements. The single door shall be located on the same color steel plate as far as possible, and the center line of double door shall be located at the joint of plate seam as far as possible, so that the color steel plate after cutting can be used as door panel. The profile connection of doors and windows shall be tight and seamless, and the dimension of the whole door corner shall be uniform.

7、内外弧的固定：与彩钢板的连接应严密，外弧柱不应连接，内弧之间的连接点定位不良，间隙严密。

7. Internal and external arc fixation: the connection with color steel plate should be tight, the outer arc column should not be connected, the connection point between the inner arc is not well positioned, and the gap is tight.

彩钢板房

Color steel house

彩钢板房规范安装十分重要，因此，建议大家选择彩钢板材料需要进行严格的选择，避免彩钢板质量不达标，施工过程中一定根据设备定位和设计图纸，检查隔墙放线定位以确定现场尺寸与图纸尺寸和设备位置是否有冲突。

The standard installation of color steel sheet room is very important. Therefore, it is suggested that the selection of color steel plate materials should be carried out strictly to avoid the quality of color steel plate failing to meet the standard. During the construction process, the setting out and positioning of partition wall must be checked according to the equipment positioning and design drawings, so as to determine whether the site size conflicts with the drawing size and equipment position.