一、选择正规的专卖店

1、 Choose a reputable brand store

经验告诉我们，市场假产品层出不穷，以次充好大有，对于不的业主一定要擦亮眼睛，正确识别真正的产品。知名专卖店的产品质量更有保证。如果没有的涂料知识，选择店是保险的了。选择型的店，这类店的油漆质量、性能和服务承诺可靠性高。其次观察油漆颜色，性油漆选用进口原料配制，亮光漆色泽水白，晶莹透明，亚光漆呈半透明，略带轻微浑浊状，无发红和沉淀现象;性油漆外包装比较精美，字迹清晰美观。

Experience tells us that fake products are constantly emerging in the market, and there are plenty of inferior products passing off as good. For unprofessional homeowners, it is important to keep their eyes open and correctly identify truly high-quality products. The product quality of well-known brand specialty stores is more guaranteed. If you don't have professional knowledge of coatings, choosing a branded store is the safest option. It is best to choose environmentally friendly brand stores, which have high paint quality, environmental performance, and reliable service commitments. Secondly, observe the color of the paint. Environmentally friendly paint is formulated with imported raw materials. The glossy paint has a water white color, crystal clear and transparent, while the matte paint is semi transparent with a slight turbidity, without redness or sedimentation; The environmentally friendly paint packaging is quite exquisite, with clear and beautiful handwriting.

二、闻气味，辨质量

2、 Smell the odor and distinguish the quality

获得质量认可的产品是有保证的，质量好，型油漆的气味应该是温和、淡雅、芳香味纯正的，劣质的油漆会有一种强烈的刺鼻气味或其它不明的异味。目前部分劣质漆也有香味，甚比香水还香，这种油漆的苯可能超标，而苯就是一种无色具有特殊芳香味的液体，对人类健康有很大的危害，因此朋友们在购买油漆时一定要闻一闻它的气味。

Products that have obtained national quality recognition are guaranteed to have good quality. Environmentally friendly paints should have a mild, elegant, and pure aroma. Poor quality paints may have a strong pungent odor or other unknown odors. At present, some low-quality paints also have fragrance, even more fragrant than perfume. The benzene of this kind of paint may exceed the standard, and benzene is a colorless liquid with special fragrance, which is very harmful to human health. Therefore, friends must smell its smell when buying paint.

涂料防水层的施工应符合下列规定：

The construction of the waterproof coating layer should comply with the following regulations:

1、涂料涂刷前应先在基面上涂一层与涂料相容的基层处理剂

1. Before painting, a layer of base treatment agent compatible with the coating should be applied on the base surface

2、涂膜应多遍完成，涂刷应该前遍涂层干燥成膜后进行

2. The coating should be completed multiple times, and the brushing should be carried out after the previous coat has dried and formed a film

3、每遍涂刷时应交替改变涂层的涂刷方向，同层涂膜的先后搭茬宽度宜为30~50㎜

3. The direction of the coating should be alternately changed during each application, and the width of the overlapping of the same layer of coating should be 30-50mm

4、涂料防水层的施工缝应注意保护，搭接缝宽度应大于100㎜，接涂前应将其甩茬表面处理干净

4. Attention should be paid to the protection of the construction joints of the waterproof coating layer, and the width of the lap joint should be greater than 100mm. Before applying the coating, the surface of the butt joint should be cleaned

5、涂刷程序应先做转角处，穿墙管道，变形缝等部位的涂料加强层，后进行大面积涂刷

5. The painting procedure should first apply a coating reinforcement layer to corners, through wall pipelines, deformation joints, and other areas, and then proceed with large-scale painting

6、涂料防水层中铺贴的脂体增强材料，同层相邻的搭接宽度应大于100㎜，上下层接缝应错开1/3幅宽 涂刷的防水涂料固化后形成有一定厚度的涂膜，如果涂膜厚度太薄就起不到防水作用和很难达到合理使用年限的要求，所以对各类防水涂料的涂膜厚度作了规定。 防水涂膜在满足厚度要求的前提下，涂刷的遍数越多对成膜的密实度越好，因此涂刷时应多遍涂刷，不论是厚质涂料还是薄质涂料均不得一次成膜。 每遍涂刷应均匀，不该有露底，漏涂和堆积现象，多遍涂刷时，应待涂层干燥成膜后方可涂刷后一遍涂料，两涂层施工间隔时间不应过长，否则，会形成分层。

6. The fat reinforcement material laid in the waterproof layer of the coating should have a lap width of more than 100mm between adjacent layers, and the joints between the upper and lower layers should be staggered by 1/3 of the width. After the waterproof coating is cured, a certain thickness of coating film is formed. If the coating film thickness is too thin, it will not have waterproof effect and it is difficult to meet the reasonable service life requirements. Therefore, regulations have been made for the coating thickness of various waterproof coatings. On the premise of meeting the thickness requirements, the more times the waterproof coating is applied, the better the compactness of the film formation. Therefore, multiple coats should be applied, and both thick and thin coatings should not form a film at once. Each coat of paint should be evenly applied, without any exposed base, missed coating, or accumulation. When applying multiple coats, the next coat of paint should be applied after the coating has dried and formed a film. The interval between the two coats should not be too long, otherwise delamination may occur.

本文由禹城钢结构板房友情奉献.更多有关的知识请点击:http://www.lxcaigang.com我们将会对您提出的疑问进行详细的解答，欢迎您登录网站留言.

This article is dedicated to friendship For more information, please click: We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message