一、场地核实??

　　1、 Venue verification??

　　在洁净地面上初次处理之后，设备定位

　　After initial treatment on a clean floor, equipment positioning

　　按设备定位、设计图纸对隔墙放线定位

　　Positioning of partition walls according to equipment positioning and design drawings

　　确定现场尺寸是否与图纸尺寸、

　　Determine if the on-site dimensions match the dimensions on the drawing

　　设备位置有相冲突的地方；

　　There are conflicting locations of the equipment;

　　?

　　?

　　对现场地面的水平进行核实

　　Verify the level of the ground on site

　　看波动是否较大

　　Check if the fluctuations are significant

　　是否有必要对彩钢板墙体底部整体校平

　　Is it necessary to level the bottom of the color steel plate wall as a whole

　　二、安装要求

　　2、 Installation requirements

　　（1）槽铝固定固定槽铝前必须先放线定位

　　(1) Before fixing the slot aluminum, it is necessary to lay out the wire for positioning

　　偏差不能超过5mm

　　The deviation cannot exceed 5mm

　　槽铝用M5x30抽心铝拉钉固定

　　The groove aluminum is fixed with M5x30 center aluminum rivets

　　间接不超过300mm有门洞位置须设置双拉钉

　　Double pull nails must be installed at doorways with an indirect distance not exceeding 300mm

　　间隔不超过50mm

　　Interval not exceeding 50mm

　　（2）T型吊梁固定吊码沿放线位置定位间距不超过1.20mT型梁与连接彩钢板固定时

　　(2) When fixing the T-beam with the hanging code along the laying out position, the positioning distance should not exceed 1.20m

　　必须用角铝或角铁压紧不得留有空隙压固体必须在两块彩钢板连接缝之上

　　It must be compressed with angle aluminum or angle iron without leaving any gaps. The compressed solid must be above the joint between the two color steel plates

　　（3）风口安装天花上的风口安装要按图纸施工

　　(3) The installation of air vents on the ceiling should be carried out according to the drawings

　　避开T型梁

　　Avoid T-beams

　　墙体上的排、回风口安装要离地200mm

　　The installation of exhaust and return air vents on the wall should be 200mm above the ground

　　（4）外观要求整体安装需平直美观不得有碰撞刮划痕迹要到才能撕保护膜板缝连接平实板缝间距3-4mm打胶要满缝平直不得有缝隙

　　(4) Appearance requirements: The overall installation should be straight and beautiful, without any collision or scratch marks. The protective film can only be torn off at the end. The board seam connection should be flat and solid, with a spacing of 3-4mm. Glue should be applied to the full seam, straight and without any gaps

　　（5）螺丝固定每一块顶板与围护板之间的固定必须有3颗钻尾螺丝围护板、立板之间连接处上下各有一颗拉钉固定边施工边固定板缝必须垂直

　　(5) Each screw fixing between the top plate and the enclosure plate must have 3 drilling tail screws. There must be one pull nail at the connection between the enclosure plate and the vertical plate, and one pull nail at the top and one at the bottom. The plate seam must be vertical while fixing during construction

　　（6）门窗安装

　　(6) Installation of doors and windows

　　门窗的安装位置和开启方向按图纸要求而定单开门尽量在同一块彩钢板上双开门的中心线尽量在板缝连接处以便切下的彩钢板做门板门窗的型材连接需严密不能有缝隙整体门拐留置尺寸必须统一

　　The installation position and opening direction of doors and windows should be in accordance with the requirements of the drawings. For order opening, the center line of the double door should be on the same color steel plate as much as possible, and the center line of the double door should be at the joint of the plate seam for easy cutting. The profile connection of the door panel and window should be tight and there should be no gaps. The overall door corner retention size must be uniform

　　（7）内外圆弧固定与彩钢板连接必须要严实外圆弧立柱不驳接内圆弧连接点之间不错位缝隙严实/

　　(7) The connection between the inner and outer arc fixation and the color steel plate must be tight. The outer arc column should not be connected, and there should be no misalignment or gaps between the inner arc connection points/

　　本文由  禹城彩钢厂 友情奉献.更多有关的知识请点击   http://www.lxcaigang.com/   真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from Yucheng Color Steel Factory. For more related knowledge, please click http://www.lxcaigang.com/ Sincere attitude. We provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Please stay tuned